Tag: G.Hn HomeGrid

Some building setups may not allow a Wi-Fi router like this D-Link Wi-Fi 6 unit to work at its best in covering the house

With Wi-Fi 7 around the corner, a company who is designing silicon for that new Wi-Fi standard is running a line that wired networks will be obsolete.

But it is a bit too hasty to state that because there are situations where the wired network will still be relevant as a backhaul for that Wi-Fi 7 wireless network. Here, I encompass both the Ethernet networks built on Category-5 or Category-6 cable along with “wired no-new-wires” networks like HomePlug powerline or G.Hn networks based on powerline, telephone wire or TV coaxial cable.

How are your premises built?

That thick wall may cause Wi-Fi not to work properly

If you find that your premises is built of dense building materials like brick, masonry or cinder-block / concrete block, you may find that you have trouble with your Wi-Fi network’s coverage. This is more so where any of the interior walls uses those kind of materials.

Examples of this may include a double-brick house that had an extension built on to it or a house that has one or more brick interior chimneys. Similarly, apartment dwellers may run in to this problem if two or more of their apartment’s interior walls touch their building’s “service core” plenums used for the elevators, garbage chutes or as “risers” for plumbing and wiring. Such a plenum is typically made of thick or reinforced concrete to satisfy noise-level or fire-safety expectations.

Another building material to watch for is metal. This may be used for reinforcement like with reinforced concrete, or it could be used as a mesh or for decorative effect like with corrugated iron used to give that rustic look. Add to this insulation material that is augmented with foil to improve its effect. This material has that “Faraday cage” effect where it reflects radio waves rather than passes them.

As well, the radio frequencies that are more affected are those at the higher end of the spectrum due to their short wavelength. This will be more so as wireless networks extend in to the 6GHz territory.

These situations will call for a wired network backhaul in order to create building-wide coverage for your Wi-Fi network.

Multiple-building setups

Methods to link buildings in a multiple-building home network

Another situation that will be of relevance to suburban and country living is the want to connect secondary buildings like a barn, cabin or granny flat to your primary house. This would also apply to the use of a caravan or campervan as secondary living quarters.

It would be more so as you think that bringing your home network and Internet to these buildings that you expect to have as part of your living or  space and is something I have covered in a feature article and infographic. Here, a wired link can earn its keep in these kind of setups and may allow you to be more flexible with building materials for the secondary buildings or main bouse.

A new-wire approach can be in the form of Cat5e cable could give up to 2.5 Gigabits per second bandwidth over 100 metres, something that would be affordable for most. If Cat6a cable was used, this could go to 10 Gigabits per second for the same length. The more premium fibre-optic technology would be able to achieve 300 metres for stability and 10 Gigabit throughput. The Cat5e setup would come in to its own with fixed outbuildings built relatively close to the main house like in most low-density living areas including most smallholdings.

Use of powerline-based “wired no-new-wires”  like HomePlug AV2 or, especially G.Hn HomeGrid, would come in to its own here. This is more so if you are renting your home or are dealing with caravans or campervans being purposed as sleepouts for example and you have them connected to your home’s mains supply.

Other factors to consider

Some devices may also cause issues when it comes to Wi-Fi coverage due to their design.

For example, a flat-screen TV will use a significant amount of metal as part of its chassis and this can act as an RF barrier. Similarly furniture made out of sheet metal like the traditional office filing cabinet can also be an RF barrier.

These “RF barriers” can effectively create an “RF shadow” if the client device is located close to them and such items are located close to each other.

It is also worth considering that wired network technologies, especially those based on Category 5 or Category 6 twisted pair copper cable or fibre-optic cable will be developed in a way to have more bandwidth than Wi-Fi-based wireless technologies. Here, it takes advantage of “pure-play” wiring infrastructure that is predictable in signal quality and reliability. This will underscore the role of these technologies as a reliable high-speed backhaul option between devices or Wi-Fi access points.

Conclusion

Due to facts like dense or metallic building materials, multiple buildings on a property or metallic objects, wired networks will still be considered relevant in the era of Wi-Fi 7. Add to this that wired networks, especially those using dedicated wiring infrastructure, will still be worked on as something that offers higher data speeds than equivalent Wi-Fi technologies.

Devolo Magic 2 Wi-Fi network extender kit that works on G.Hn HomeGrid powerline network technology

The International Telecommunication Union’s G.Hn HomeGrid standard is expected to become a significant new direction in “wired no-new-wires” network technology. Such technology makes use of wiring infrastructure that is in place within a premises for purposes such as providing AC mains power, providing a telephone service or connecting a TV to an outdoor TV antenna or cable / satellite TV setup.

This is for both the in-premises local-area network and for the Internet / WLAN “access” network that brings your Internet service to your home-network router.

This technology primarily works as an alternate powerline / AC-wire network technology to the established HomePlug family of powerline-network technologies. But it is also competing with MoCA for the TV coaxial-cable medium and the G.Hn HomeGrid Forum took over the HomePNA standard for phone-line-based on-premises networks.

Media types

Powerline

Use of a building’s AC wiring infrastructure is considered more credible due to the fact that there are many power outlets across a typical home. I have even had good experiences with this kind of network especially for extending Wi-Fi coverage or even extending a home network out to a detached garage that served as a “man-cave”.

The HomePlug Alliance had effectively abandoned continual development of the HomePlug series of powerline-network standards. At the moment, the latest standard is the HomePlug AV2 MIMO which can go to 2000Mbps,  That is although a significant number of device manufacturers and IT retailers are continuing to make devices that work to the 1200Mbps bandwidth.

G.Hn HomeGrid has taken the powerline network further by offering the HomeGrid MIMO variant that cam move at least 2000Mbps of data. Like the HomePlug AV2 MIMO standards, this uses the active / phase / line, neutral and earth / ground wires of the mains-power plug to carry the data, thus assuring users of robust data transmission across a building’s general AC wiring infrastructure better.

G.Hn HomeGrid powerline technology could appeal to apartment blocks where multiple powerline-based “wired no new wires” networks could exist

The G.Hn HomeGrid powerline network standards have been refined also to increase data transmission robustness where there are many powerline networks operated together. This would be, perhaps, a situation that takes place within a large multiple-premises building like an apartment block, shopping centre or office block and would suit today’s urban-design expectations of mixed-use multi-premises developments. Some people would also hold this true for a dense neighbourhood of terrace / townhouse, semi-detached or similar homes.

A G.Hn HomeGrid powerline network can co-exist with a HomePlug AV2 powerline network in the same building but isn’t directly compatible with each other. This is similar to first-generation HomePlug powerline networks operating alongside second-generation HomePlug AV / AV2 powerline networks.

Personally I see G.Hn HomeGrid being used to “take the powerline network further” to higher bandwidths, increased robustness, further distances (500 metres compared to 400 metres for HomePlug AV2 MIMO) and other future needs.

At the moment, Devolo are investing in this technology with their Magic series of powerline network products including some Wi-Fi access points and offering some of these devices to consumers.

But some other network-equipment vendors who have retail-market presence are offering at least a powerline-Ethernet adaptor that works to G.Hn HomeGrid standards as part of their powerline-network product ranges. It is a way for them to put a foot in the door for higher-bandwidth powerline network segments.

TV coaxial cable

Another medium type that is supported by G.Hn HomeGrid is the TV coaxial-cable infrastructure. This would be associated with cable TV, an outdoor TV antenna (aerial) or a satellite dish and there may be extra TV coaxial-cable sockets installed around the house so you can have additional TV sets or use an easily-moveable TV in other rooms.

The Multimedia Over Coax Alliance have created a standard for using TV coaxial-cable infrastructure. But G.Hn HomeGrid have seen intention in using this same medium for the same purpose and could be working it to higher capacities or increased robustness.

Phone line

Yet another medium type that is supported by this same standard is traditional telephone cabling. This was worked on by HomePNA but the HomeGrid Alliance took over that concern and embodied it in to the G.Hn HomeGrid standard.

This infrastructure would have come about for established homes where there are multiple phone sockets installed through the house’s lifetime. This would be due to the installation of extension phones or to allow one to move a corded phone between different locations easily before cordless phones became a cost-effective approach to flexible landline telephony.

Use profiles

The G.Hn standards implement two relevant use profile cases.

One is called HomeGrid which describes connecting network devices within the premises as part of a local area network.

The other is called Gigawire and is described as being for “access” connectivity. This is to connect between the network’s router WAN (Internet) connection and a modem that is used for providing Internet service. This use case encompasses fibre-copper setups within extant multiple-premises buildings used to provide Internet to each premises with the building. Or it can encompass a single-premises building where the modem associated with the Internet service is installed in an inconvenient location but the Wi-Fi router has to be installed in the centre of the premises for best results.

All of the media connectivity types such as powerline, phone line or TV coaxial cable are able to work in these different use profiles. But there is a question about whether the same medium type could be used for access or in-home connectivity at the same time.

Media-type agnostic approach

The G.Hn HomeGrid standard is being underscored as a media-layer-level standard for the “wired no-new-wires” networks with the goal to make it easier to bridge between different media types.

This could be about the arrival of lower-level bridge devices that link between the different media types with these devices not needing higher-level processing to do so. Most likely such devices will have the bridge functionality but also have a Cat5 Ethernet connection of some sort.

Further evolution of this standard

Currently this standard is being implemented as a “wired no-new-wires” approach to creating a multi-gigabit home network that has a bandwidth of 2.5Gbps or greater. It is to complement multi-Gigabit Ethernet and Wi-Fi 6/6E wireless network technology in raising your home network’s bandwidth making it fit for multi-gigabit broadband Internet services.

But there is further work needed to come about from G.Hn HomeGrid Forum for certain issues. For example, there will be a need to support VLAN network setups using the “wired no-new-wires” technologies. This would come in to play with routers that support a “guest network” or “community network” in addition to a primary network; or for VLANs that are used as a quality-of-service measure for VoIP or IPTV setups.

They would also have to examine the use of an access network and an in-premises network working on the same media bearer.

This could work with a fibre-optic extension setup that would normally use a G.Hn HomeGrid access network on a particular media type like phone line, power line or TV coaxial cable to bring the WAN (Internet) link from a garage or basement where the fibre-to-the-premises optical-network-terminal is installed to the living area where the home network router is installed. But the situation would change where that same basement or garage is purposed as a living space of some sort and a G.Hn HomeGrid in-premises LAN segment is to be created to make that space part of your home network.

Or there is the idea with a multiple-premises building where G.Hn HomeGrid technology is used for the in-building access network to each premises but there is a desire to extend a premise’s LAN or Wi-Fi to a common living area within the building.

Conclusion

The G.Hn HomeGrid and GigaWire standards are something that we have to watch and consider when it comes to “wired no-new-wires” network links for our home networks. In some cases, this technology may be about a “clean-slate” approach to your “wired no-new-wires” network segments.