Tag: HomePlug AV

What these HomePlug AV wireless access points are about

I had come across this Tweet that was shared on to Solwise’s home page concerning how quick it was to extend a small Wi-Fi network using a HomePlug AV wireless access point. As the picture showed that, once in place, this looked discreet and didn’t use any extra cables. You also had the advantage of being able to relocate this access point if you needed to such as focusing more coverage on another area.

Expect a lot more reliability and proper bandwidth from your Wi-Fi wireless network coverage when using a HomePlug wireless access point to extend that home network.

Don’t forget HomePlug powerline networking in your home network setup

HomePlug AV adaptor

The HomePlug powerline adaptor – part of a wired no-new-wires segment that is worth considering

I have often seen network setups pitched especially at consumers as to be the wireless network. Typically this is about an 802.11n Wi-Fi segment hosted by a wireless router with 802.11n range extenders used to boost the signal coverage out further. Having a wired backbone for one of these networks typically has us thinking of Ethernet as the way to go but if you want it to look neat, you have to have the Ethernet cable pulled through your home which only works well if you are building or renovating your home.

Another technology that is easily forgotten about is HomePlug AV powerline-network technology. This technology uses the AC wiring in your home as a wired-network backbone. This initially existed in the 1.0 format with 14Mbps data transfer and graduated to 85Mbps. Now it is available as a HomePlug AV setup which works at 200Mbps or a HomePlug AV500 (IEEE1901) setup that can work at 500Mbps.

Just lately, there have been the arrival of HomePlug AV2 devices that provide increased robustness for the data as well as working at 600Mbps or 1.2 Gigabit speeds in newly-released varieties. The increased robustness comes about due to each device on the HomePlug segment serving as a repeater as well as use of all three wires including the “earth / ground” wire of the AC wiring setup for the data transfer.

Similarly, choosing a HomePlug adaptor with a built-in AC socket can lead to more reliable operation due to the fact that he integrated AC outlet is filtered in a way to prevent electrical noise from the device you plug in to it getting in to the AC current. This noise, typically generated by a lot of switch-mode power supplies used in today’s electronics, can impair the data communication on the HomePlug network segment that is sharing the same AC line.

The devices typically come in HomePlug-Ethernet adaptors with some of them having a multiple-port Ethernet switch in them and, in the UK especially, a HomePlug-Ethernet adaptor which directly plugs in to the wall and has one Ethernet socket is typically referred to as a “homeplug”. This means that you connect your computer, router or other network device to the HomePlug device using an Ethernet cable.

It is worth noting that a few HomePlug-Ethernet adaptors are appearing that also work as Power-Over-Ethernet power-sources according to the 802.3af or 802.3at (high-power) standards. This means that they can supply power to network-connected devices that take power via their Ethernet connection and it leads to one cable between these “homeplugs” and the network-connected device as well as not needing to consider extra power for these devices. The key applications that these adaptors serve well would be Wi-Fi access points, IP-based surveillance cameras or VoIP desk telephones where there is a desire to run one thin wire to these devices.

There are also a few HomePlug devices which have an integrated Wi-Fi access point along with an Ethernet connection and these are pitched at the idea of extending the coverage of your Wi-Fi wireless network segment without losing the bandwidth available which happens with wireless range extenders.

Where do I see the HomePlug powerline network fit in

I see this network fit in as a supplementary “wired no-new-wires” network segment suitable for a variety of reasons. For example, if you aren’t wiring your premises for Ethernet, you can use a HomePlug segment to provide reliable wired network connection for normally-sessile devices like smart TVs and video equipment, printers and the like. Even if you do have an Ethernet segment, you can use a HomePlug powerline segment as an infill measure to cover parts of the house that you don’t have Ethernet connections in.

HomePlug comes in to its own with a temporary wired network where you don’t want to use extra cables. This comes in to its own when you are repositioning furniture on a trial basis before you commit to calling in electricians to pull Ethernet sockets for your new setup; or a small shop where you want to shift the POS system during a sale or special event. As well, HomePlug comes in to its own as a wired network for rented premises where you are not allowed to or it’s not worth the resources to pull extra wiring through the walls.

There are even some places where HomePlug technology is the only cost-effective network technology to assure premises-wide network coverage. These are where a place has, for example, a very thick dividing wall or remnants of a disused fireplace, that is not worth the cost and time to pull wire through and Wi-Fi wireless networks will not perform adequately past that wall.

HomePlug link between house and garage

HomePlug – to connect the man-cave to the main house

In some cases, HomePlug can work well with linking an outbuilding like a garage, barn or cabin / granny-flat to the main house’s network and Internet connection. I have even successfully set up one of these arrangements successfully to link a garage that was purposed as a “man-cave” to the home network and Internet that existed in a suburban home.

What needs to be done

Retailers and Internet service providers need to do their bit to promote HomePlug technologies and the concept of having two or more network media in a small network. This includes using a wired backbone and access point to “push out” a Wi-Fi segment or using something like HomePlug to connect your home theatre to your home network.

One positive step that is taking place is nVoy which allows a single point of control to apply between Wi-Fi, HomePlug, MoCA and Ethernet to allow for “best case” data transfer and simplified network configuration. Here, this could come in to its own with creating the business-grade “extended service set” for the Wi-Fi segment where you have two or more access points connected to an Ethernet or HomePlug backbone and with the same SSID and security parameters. Once this is established in the marketplace, there needs to he help with exposing the reality of complementing network media providing the home network that works smoothly.

How to give this a go

One device and situation you could target with HomePlug AV in your existing network would be your games console or smart TV and setting this up to work with this technology when bridging it to the home network. This is more so if you haven’t wired your home for Ethernet or haven’t put an Ethernet connection where the TV currently is.

Similarly, repositioning your Ethernet-capable network printer to somewhere where it looks better to you and suits your needs better could be a chance to implement a HomePlug network setup in your network.

Here, it is simply about giving the HomePlug powerline segments a go as a “wired no-new-wires” medium to connect devices to your home network and is something I underscore on this Website.

This article has been updated on January 2014 but has been updated to reflect the existence of HomePlug adaptors that can power network devices using Power-Over-Ethernet. As well, I have added a use-case regarding linking an external building like a garage or barn to the main house’s network and Internet connection.

At last a HomePlug wireless access point that simplifies the wireless network extension process

Article – From the horse’s mouth

TP-Link

TL-WPA4220 – Welcome to TP-LINK (Product Page)

My Comments

One main reason most of us would buy a HomePlug-based wireless access point is to extend the coverage of that Wi-Fi wireless network past that radio obstacle like the double-brick interior wall without needing to pull new cabling. Or you don’t want to butcher your garden or dig up your lawn so you can reliably extend your home network with its Wi-Fi wireless segment to that garage or bungalow.

But a setup hurdle that one can easily end up with is copying the SSID (wireless network name) and network security parameters from your existing wireless router to the access point and making sure these are accurately copied so you can have proper roaming operation for your wireless network.

TP-Link have made this simple through the use of a “Wi-Fi Clone” button on the TL-WPA4220 access point. Here, this access point uses the WPS-PBC “push-button” setup routine to learn the parameters associated with your small wireless network segment.

This procedure has to be performed with this HomePlug access point in good Wi-Fi range of a router or access point that implements WPS push-button setup.You push the WPS button on your suitably-equipped wireless router as if to enrol a new device to your home network, then push the “Wi-Fi Clone” button to complete the procedure. This means that the access point has what is needed to be part of the Extended Service Set which is you home network’s Wi-Fi segment.

From that point on, you just simply establish that HomePlug AV powerline segment as the backbone for your wireless network and benefit from the increased coverage. But I would personally have this access point equipped with the WPS client setup mode for enrolling client devices close to it to avoid the need to traipse back to your wireless router to enrol that Android smartphone or Internet radio that is to be used in the remote area.

What I see of this is that steps have been taken in the right path to move away from the so-caled “range extenders” towards a more reliable and proven method of extending a wireless network’s coverage by simplifying the tasks required for achieving this goal.

Feature Article – Having the online life in that private space

Introduction

Most of us have one or more private spaces in the home that aren’t really where we sleep in but want to retreat to when we want to spend time alone or with a few chosen people. This may, for men, be the classic “men’s shed” or “office-den” but is becoming the so-called “man-cave”. For women, it may be a private lounge area or study with some people purposing these spaces for personal religious activity amongst other activities.

HP Envy 4 Touchsmart Ultrabook at Intercontinental Melbourne On Rialto

HP Envy 4 Touchsmart Ultrabook – an example of a touch-enabled Ultrabook that can be moved around very easily

Some of these spaces may also be used as a reception space for one’s own group of friends such as a man’s “mates” or a woman’s own “lady friends”, as well as serving as the own space. This is more so if they want to meet with these people away from the rest of the crowd in the house.

In most of these areas, it may be appropriate to be able to engage in online life using the home network. It encompasses access to the resources available via the home network whether it be music and video content held on the NAS or the ability to print out documents on a network-capable printer. The activities may range from personal entertainment in these areas through researching information from the Internet to creating documents and Web content.

What can you use here?

Sony VAIO Tap 20 adaptive all-in-one computer

Sony VAIO Tap 20 – an example of an “Adaptive All-In-One” computer

You may want to use a portable computer device whether it be a laptop / notebook or tablet computer so you can take it between your private space and other spaces. For a fixed setup, you may go for an all-in-one or low-profile desktop computer. Some systems like the Sony VAIO Tap 20 may be able to bridge the gap between a large-screen desktop and a laptop computer and some of the regular all-in-one computers may be light enough to be transported from room to room.

The portable computer or easy-to-transport “all-in-one” computer would be more important if you are dealing with a space that is accessible directly from outside and doesn’t do well for security. This is because you can easily take the computer in to your home so it doesn’t tempt thieves when you have finished in that space.

Sony SA-NS510 Portable Wireless speaker

Sony SA-NS510 Portable Wireless Speaker

If you are thinking of online-capable audio or video equipment that can fit well in this space, there is a lot of the equipment that can suit your particular needs. For example, a small Internet radio could be the answer for a shed or garage like as I have seen with the Kogan Internet radio that I reviewed in this site’s early days. Here, a person who was living with me had this radio in the garage playing some content from BBC Radio 4’s Internet feed while he was doing a few repairs at the workbench. A small Blu-Ray-equipped home-theatre system of the same ilk as a Sony BDV-E2100 or Yamaha MCR-755 or a small hi-fi of the ilk of the Sony CMT-MX750Ni or Denon CEOL Series could play its part as an entertainment system for a den.

You can even use the home-theatre systems with an LCD computer monitor as the display device if the monitor has an HDMI input socket or DVI socket that is compliant with HDCP. This can mean that you don’t need to use a TV set with these devices especially if you use a DLNA-compliant broadcast-LAN tuner or just enjoy media held on optical disc or the home network.

Denon CEOL Piccolo music systemOn the other hand, you could use a Bluetooth or Wi-Fi wireless speaker system along with your smartphone, tablet or notebook to play audio content from more than the speaker built in to the computer device. Similarly, you could connect a Bluetooth audio adaptor or AirPlay/DLNA-compliant network media receiver to a pair of computer speakers or a small boombox that has a line input to achieve the same goal.

What needs to be done

Network connectivity

Here, I would make sure that you have reliable access to the home network from this space. If the space is located in another building, I would suggest that you pay attention to my article on multiple-building home networks.

Western Digital LiveWire HomePlug AV Ethernet switch connected

The WD LiveWire HomePlug AV switch that fills in the network gap

In some cases, I would make sure there is an Ethernet connection in that area if your place is being wired for Ethernet and you can afford it. On the other hand, you could use a HomePlug AV powerline connection to that space. This is important for detached buildings or rooms with direct outdoor access where they may not be secure because you can take the HomePlug adaptor in to your home. It is also important if you don’t get good Wi-Fi wireless-network reception from your router in that area and this situation can be remedied using an access point connected to the wired backbone.

Access to live TV content

As for access to TV content, if your space doesn’t have a connection for a TV aerial (antenna) or cable / satellite TV, you could use the home network to gain access to TV content. This is facilitated with a broadcast-LAN tuner like HDHomeRun or Devolo dLAN Sat which is connected to the TV aerial, cable or satellite TV depending on the device and transmits your chosen broadcast signal down the home network. Then you use software on the computer or tablet to “tune in” to the broadcasts. For that matter, the HDHomeRun Prime offers access to antenna or US cable TV you subscribe to via DLNA-capable video devices and software.

On the other hand, if you have pay TV, you could benefit from the provider’s “TV Everywhere” solution which works with regular or mobile computer devices to show live or on-demand pay-TV on these devices using your home network.

Access to your network-hosted content library

For audio, photo and video content, you can use DLNA-capable software media players like Windows Media Player 12, or TwonkyMedia to play the content on your portable computer or mobile device. If you use any of the Apple platforms, you could set your NAS up as an iTunes server for the audio content and have the iTunes music player software on your device pull up this content.

As I have mentioned before, devices with network-media-playback functionality would have to work to DLNA and/or AirPlay standards if you want to use these as your media player for your small space.

Printing from your private space

You may not need to worry about having a printer installed in that “man cave” or similar space if you are using a network-accessible printer. This means that you don’t have to worry about factoring in space for the printer. The only exception to the rule is if you see this space as a home office and you may want to have a heavy-duty machine for turning out work related to your business or similar effort.

Conclusion

Here, you can set up a reliable personal computing and entertainment environment that you can use in your small personal space, with the equipment being more suited to that space.

At last HomePlug AV and Power-Over-Ethernet in one device

Article

Asoka PL9660-PoE PlugLink 200 Mbps Powerline Adapter w/ PoE Reviewed – SmallNetBuilder

From the horse’s mouth

Asoka USA

Product Page

My Comments

Introduction

I have often heard the line that the Power-Over-Ethernet technology, which supplies power to a network device connected via twisted-pair Ethernet cable using that same cable, and HomePlug powerline-networking technology are mutually exclusive technologies.

What is Power-Over-Ethernet and what is it used for?

The common 802.3af and 802.3at Power-Over-Ethernet technologies make use of the Category-5 “twisted-pair” Ethernet cabling that is used to transfer data to the network also as a power-supply cable. The main advantages are that you don’t have to have an AC outlet close to a network device and you can just run one cable to that device to allow it to function.

The typical implementation is either an Ethernet switch that has Power-Over-Ethernet ports providing power to a VoIP desk telephone, wireless access point or IP-based video-surveillance camera. This appeals to businesses as a way of providing centrally-managed power for these devices as well as allowing for simplified cost-effective installation and reliable operation.

What is HomePlug AV powerline network technology

The HomePlug AV network technology uses the building’s existing AC wiring as a data conduit. This provides a “no-new-wires” wired network setup for homes and other installations where it is not cost-effective to have Ethernet wiring in place and has shown a strong appeal for temporary wired-network setups.

Even if a building has Ethernet wiring in place, the HomePlug AV technology works as a way of extending this network in a temporary or semi-permanent manner. In some cases, the HomePlug technology can work as a cost-effective wired network link between a house and an outbuilding such as a detached garage if there is AC wiring in that building which isn’t separately metered.

Of course most of these network segments have network client devices connected via a short Category-5 Ethernet cable to a HomePlug-AV-Ethernet bridge adaptor typically referred to in the UK as a “homeplug” in the case of the common single-port wall-wart device.

Why am I impressed with the Asoka PL-9660POE “homeplug”

This adaptor is both a single-port HomePlug-AV-to-Ethernet network bridge along with a Power-Over-Ethernet power supply according to the 802.3af standard. Here, I could connect a Wi-Fi access point or VoIP desk telephone that can be powered using Power-Over-Ethernet to this device and it provides power to that access point while linking it to the HomePlug AV powerline-network backbone.

The advantages seen here is that I only use one AC outlet to link the network device to the HomePlug segment as well as providing power to it rather than having to have another AC outlet or double-adaptor being used for another wall-wart. You also benefit from only needing one cord between the device and this HomePlug adaptor which is easier to manage in to an aesthetically-pleasing setup. This is of importance when you are using an wireless access point to extend your wireless network and you would find that having that access point up high with a clear line of sight to the laptops, tablets and smartphones used in that area would yield optimum network performance and battery runtime for the mobile devices. It is compared to using a HomePlug wireless access point which will typically be installed at floor level and obscured by furniture and may not be able to perform adequately.

What about transportability when you are thinking of that VoIP desk telephone? Typically, a furniture and equipment arrangement may suit one’s current needs but these needs do change. This adaptor may allow you to reposition the phone to a newer location as you see fit even in a semi-permanent manner such as if you are moving the cash-wrap stand in your shop to a newer location to cater for a sale or you simply wanted to bring the VoIP conference phone out only when needed.

This device may also help with legitimising the Power-Over-Ethernet technology for the home network. Examples of this could include “two-piece” HomePlug access-point kits; small consumer-AV applications like tabletop Internet radios, network speakers or digital picture frames; or even all-in-one computers that can be powered through the Ethernet conneciton. To the same extent, computers like tablets, small notebooks and “adaptive all-in-one” computers of the same ilk as the Sony VAIO Tap 20 can benefit from using their Ethernet port as a power connection option to charge up their batteries or allowing the user to avoid compromising battery runtime,

Even an Internet-gateway router could be powered using this method as an alternative to the separate power brick that these devices come with. As well, using a Power-Over-Ethernet power splitter which provides 12 volts or 5 volts DC to a device that isn’t capable of Power-Over-Ethernet from an 802.3af Power-Over-Ethernet connection could yield benefits to the home network by eliminating the need to use a “wall-wart” or “power-brick” and a separate AC outlet to power network devices.

Points of improvement with this device

Here, the HomePlug standard that this device supports could be the HomePlug AV 500 / IEEE 1901 standard for better data throughput. This is more so as this standard becomes the norm for most HomePlug AV segments. As well, a variant that supports the 802.3at Power-Over-Ethernet Plus standard could be made available and pitched towards set-top-box applications. But these improvements may require further power-supply engineering to cater for higher power loads.

Similarly, the Asoka “homeplug” could be made available under an OEM-contract to other vendors to sell to customers so as to make the concept more ubiquitous. For example, having this fitted with the Continental-standard AC plug and sold in to France could work hand-in-glove with the “décodeurs” (TV set-top boxes) that are part of the many “n-box” triple-play Internet services offered in that country. Here, these would work as a convincing easy-to-implement alternative to a “homeplug / power-supply” box like the Freeplug that is used to link the “n-box” Internet gateway device and the “décodeur” set-top box. These boxes typically have three wires with one to the power outlet and two to the “n-box” or “décodeur” device.

Conclusion

I just hope that this device isn’t just a “flash in the pan” when it comes to HomePlug and Power-Over-Ethernet but a way to prove to the industry that these technologies complement each other.

Buffalo offers a HomePlug AV500 and Wi-Fi N300 kit that can work as a router

Article

Test 59H: Kit CPL Powerline 500AV Wireless-N Router Starter kit (France – French language)

From the horse’s mouth

Buffalo Technology

Product Page

My Comments

Buffalo Technology are offering to European customers a HomePlug AV500 / Wi-Fi N300 access point, known as the WPL-05G300, which isn’t just a HomePlug / Wi-Fi access point for that existing small network. Here, this device doesn’t just allow you to also connect to an Ethernet segment but can be set up to become a wireless router while serving the other Ethernet segment. This is due to two Ethernet connections on the same device

The fact that it can become a router may please some users who may use a broadband modem like most cable-modem deployments and some next-generation broadband and ADSL2 deployments. But the router functionality would be considered irrelevant to most European users who typically run a modem-router which has the integrated Wi-Fi functionality.

Personally, I do see this device still relevant as the secondary access point to “fill in” those Wi-Fi reception gaps such as what is created in older European properties that use thick brick, cement or stone walls. This also includes a lot of the UK properties that have remnants of fireplaces that have been blocked off.

What I am pleased about with this device is that there are switches on the unit to select between the router and access-point mode and similarly to select between client-bridge and access-point behaviour. I am not sure if this is true but this could allow for “quick setup” of extension access points through the use of WPS.

This device is available as a pair of two of these access point / router devices which could come in handy as a way to create that HomePlug segment and increase Wi-Fi coverage or create a 802.11g/n “N300” Wi-Fi segment. Similarly, the kit could also answer outbuilding network needs or encompass that old caravan in the home network. Caravan-park owners could also lick their lips at this setup with the ability to provide reliable wireless coverage in their tenants’ vans.

Who knows who else will offer similar devices that can capitalise on HomePlug AV technologies to create capable no-new-wires small networks.

Consumer Electronics Show 2013–Part 2

Introduction

I am continuing from where I left off with Part 1 which focused on the home entertainment aspect such as the 4K UHDTV screens and the games consoles that are to put Sony and Microsoft on notice.

Computers

With Windows 8 already launched, the trend for computers is to see more of the ultraportable computer that come either with a touchscreen or a Windows-8 multi-touch trackpad. Most manufacturers are running with at least one convertible ultraportable model that has swivel-screen, 360-degree hinge or a slide-out design as well as a detachable-keyboard hybrid tablet in order to catch this user interface.

The consumer desktop computers will typically manifest as a touch-enabled all-in-one unit alithough a lot of the 21” large-screen tablet computers of the same ilk as the Sony VAIO Tap 20 are surfacing for this category. THe concept is augmented through the use of “one-machine multi-player” hybrid video/board games that can be played using these touch screens.

Another trend that is appearing for some of these products is the display having an increased pixel density with 1080p resolution appearing on 13” and smaller screens or 4K and similar resolution displays appearing on the mainstream screen sizes. This has been driven by Apple’s implementation of high-pixel-density “Retina” displays in some of their MacBook lineup. Of course, Windows 8 would have native support for adapting its Desktop and Modern user interfaces to these higher pixel densities and most software developers would be encouraged to adapt to the newer pixel densities.

Acer is launching the Aspire S7 Ultrabook and the Iconia W700 and W510 detachable-keyboard tablets. Dell has also launched a 1080p display as an option for the XPS 13 Ultrabook.

Toshiba have provided newer products such as the Satellite U845t which is a touchscreen Ultrabook that runs for approximately US$800. This 14” (1366×768) WIndows 8 computer has an option of an i3 or i5 CPU, 500Gb on the hard disk and 32Gb SSD cache, up to 6Gb RAM and equipped with HDMI, Ethernet, SDHC card slot and 3 USB ports (1 with USB 3.0). Here, they intended to position the U845t as the Ultrabook equivalent of the “reasonably-priced car”.

They also ran with the Qosmio X875 which is a gaming laptop with a 1Tb hybrid hard drive with 8Gb SSD cache. It also has the “Black Widow” performance design with up to 32Gb RAM, up to 2Tb storage and a 3GB NVIDIA GTX 670M GPU display and NVIDIA 3D as an option.

On the other hand. HP are launching 2 affordable “Sleekbook” ultraportables that are driven by AMD processors. Both of these are what you would call a “lightweight mainstream” laptop with a 15.6” screen, replaceable batteries, numeric keypads and multi-touch trackpads. They also have Dolby sound tuning as a way to make that music or video sound better. The basic model comes with the A6 processor, 6Gb RAM and 500Gb hard disk storage while the premium “Touchsmart” variant comes with a touchscreen, the faster A8 processor, 6Gb RAM and 750Gb hard disk storage.

Lenovo exhibited their Horizon 27 touchscreen desktop all-in-one which is able to work as an “action table”. As well, Lenovo are planning to “split” their brand by having the Lenovo brand for home and small-business computing equipment and the “Think” brand associated with “ThinkPad” and “ThinkCentre” for their large-business computing equipment. This direction reminds me of Ford’s and Chrysler’s Australian operations in the late 60s and early 70s where they were trying to run a separate brand for their luxury cars with “LTD” and “Landau” for Ford’s efforts and “VIP” for Chrysler’s efforts.

Panasonic were showing their 20” 4K-display “VAIO-Tap-style” tablet with Windows 8 as a prototype for their computer entry.

Dell launched their Latitude 10 essentials tablet which is their effort at pushing the price of a full Windows 8 tablet down to a reasonable price of US$499. This has the Intel microarchitecture and comes with a 10” screen as well as 32Gb of SSD storage. They also issued a 1080p screen option for their XPS 13 Ultrabook.

Gigabyte have fielded an extra tiny desktop PC with Intel i7 horsepower. This machine is a similar size to the Apple Mac Mini, but like machines of this ilk, you don’t have room to expand compared to larger computers.

ASUS also fielded the Transformer all-in-one tablet which can boot Android 4.1 and Windows 8. It has for its display an 18.4” screen with 1080p resolution.

Regular computer technology

Intel has been tweaking the Atom CPUs as a stronger system-on-chip for low-tier portable computing and released limited runs of the Ivy Bridge chipset which are tuned for power conservation and system performance.

Peripherals

Computer monitors

There are some technologies that are appearing for this class of device such as the increased pixel density such as a 4K UHDTV screen (2560×1440) for 20” and above or 1080p HDTV (1920×1080) for lesser screen sizes, use of a 21:9 aspect ratio, affordable IPS LCD displays and touchscreen displays.

Here, LG had launched a 4K 30” screen as well as the EA93 21:9 screen which has a 2560×1080 resolution and 4-way split abilities. Similarly ASUS launched an ultrawide 21:9 monitor with similar specifications to this monitor. As well, Sharp had exhibited a 32” 4K-resolution monitor which is the thinnest in this class. This IGZO-driven screen comes in at a thickness of 1.5”.

HP had launched a run of 20”-27” monitors such as the deluxe Envy 27 that has an elegant bezel-free IPS display, HDMI digital audio with optical SPDIF output as well as a 3.5mm pre-out jack. It has the above-mentioned HDMI connector, a DisplayPort connector and a legacy VGA connector. The sound subsystem in this model is, like most of the premium and midrange HP consumer laptops, tuned by BeatsAudio.

The Pavilion xi Series (20”, 22”, 23” 25” and 27”) has IPS and the full input complement (VGA, DVI and HDMI). Except for the 20” variant, they can work with the 1920×1080 resolution. The Pavilion P Series (18.5”, 20” and 21”) are pitched as the “budget business” models which can work at 1366×768 or the 20” and 21” models can work at 1600×900 resolution.

They also released the U160 which is a USB-powered portable DisplayLink monitor. This 15” screen, which works at 1366×768, comes in a leather case and is pitched to work as a second screen for that ultraportable notebook computer.

Speaking of DisplayLink, the organisation that represents the “display over USB” concept has demonstrated a “single-pipe” USB 3.0 external-display setup. This “proof-of-concept” uses one USB 3.0 cable to provide external power to the laptop alongside the transfer of display, USB-peripheral, audio and Ethernet between the laptop and the monitor. It is more about the idea of encouraging the development of a USB monitor dock which is effectively a laptop power supply, USB hub, Ethernet network adaptor and external display and audio. As well, the DisplayLink MacOS X driver has been updated to work with 4 adaptors using USB 3.0 technology.

ASUS exploted the DisplayLink concept further with their VariDrive expansion module. This is a laptop expansion module that has a DVD burner, DisplayLink video to HDMI or legacy VGA devices, Ethernet and Audio via HDMI and connects to that ultraportable via USB 3.0.

Network technology

802.11ac Wi-Fi wireless

There is an increasing number of wireless routers, access points and USB “stick” client adaptors that work with the new draft 802.11ac wireless-network specification.

These are are also being equipped with performance-improvement and QoS-optimisation chipsets from the various chipset vendors. An example of this is Qualcomm’s StreamBoost technology which manages the WAN (Internet) and LAN (home network) sides of the equation for optimum throughput for the small network.

As well, D-Link have launched an online-gaming-optimised 802.11ac Gigabit router with the Qualcomm Atheros VIVE technology. Netgear are also making for an easy-to-set-up experience for their newer routers by implementing the QR codes on their management user interface so you can integrate your Android phone to the home network very quickly. They also fielded the D600 which is the first 802.11ac DSL modem router that can work with today’s ADSL networks. But it also has a Gigabit Ethernet WAN connection for use with next-generation broadband.

Of course, most of the router manufacturers are touting cloud technology for this product class. This is primarily about remote access to data held on storage that is attached to these routers via a Web interface or a client-side mobile app.

Shoehorning the home network, and the HomePlug technology

There have been a few interesting devices that can improve your home network.Firstly, NETGEAR have shown a plug-in simultaneous-dual-band wireless range extender / Wi-Fi client bridge that offers a feature that snaps at the heels of the Apple Airport Express. Here, this device has AirPlay / DLNA audio playout so you can connect an amplifier or a pair of active speakers and push audio content from your smartphone, tablet, laptop or desktop PC through that amplifier or speakers. At the moment, I don’t know if this device can also work as a regular access point.

The HomePlug AV specification is still pushed as a “wired with no-new-wires” option for the home network and Engenius have released a device that capitalises on this fact. It combines a HomePlug AV 500 bridge, a 5-port Gigabit Ethernet switch and an 802.11n N300 Wi-Fi access point as the ultimate network-hub option for the far end of the house, the old bungalow or that funky old 1970s caravan that is serving as a teenager’s sleepout or extra office.

For that matter, HomePlug network technology isn’t just showing up as network-infrastructure hardware but as being integrated in connected devices. This is more so with a Netgear Airplay audio adaptor / USB server and some of Hisense’s latest connected TV designs. As well, other chipmakers like Broadcomm and Sigma are supplying chipsets for at least the HomePlug AV specification. This could reduce the cost of the hardware for this network segment.

Similarly, the HomePlug AV2 Gigabit MIMO standard which exploits the earth wire as well as the active and neutral wires in the mains wiring is coming closer. This is expected to yield good things for the home network such as each node being a repeater as well as this “no-new-wires” technology hitting the Gigabit mark.

Portable routers

AT&T and Sierra Wireless used this show to launch the second model of the touch-screen MiFi. But this one is equipped with the 4G LTE as its WAN (Internet) connection.

D-Link also exhibited the SharePort Go 2 which is a pocket-sized 802.11g/n Wi-Fi router that works with an Ethernet connection or a USB wireless-broadband adaptor. The Wi-Fi segment is the only LAN segment available to this travel router but it can also share content held on an SD card.

Printer technology

There hasn’t been much happening for printers at this year’s CES. Typically new models may be launched at separate events like CEBit in Hannover, Computex in Taipei or Photokina in Cologne due to some focusing on small-business needs or photography printing needs. As well, the manufacturers run their own events to launch their own printers.

This is  although Canon had launched the PiXMA MX392, MX452, MX522 and MX922. These have in common high-capacity cartridges with a front-load design similar to Brother inkjets and the HP OfficeJet Pro 8600a series. This is a welcome move away from having to open a lid on the printer when the ink runs out.  They are also optimised with a high duty cycle which would also please business owners who want a lot more out of them. Most of the networked models in this series also are set up for Google Cloud Print.

Storage Technology

Toshiba has shown a microSDHC card reference design which implements the TransferJet technology. This is a near-field wireless data transfer for microSDHC devices rather than having this integrated in the device’s electronics. I wonder how the operating systems would cope with the idea of this technology so you can select files to transfer but this could work well for cameras and MP3 players.

Seagate have premiered their Wireless Plus mobile NAS which is like the GoFlex Satellite except it has a larger capacity of 1 Terabyte. Surprising for this product class, this unit is the first mobile NAS to implement DLNA MediaServer technology so it could stream to Internet radios, smart TVs or DLNA media player software.

They also launched the Central NAS which works with a Samsung TV app or can stream to any DLNA-capable media device. It could then mean you can do more with your files at your Samsung smart TV rather than just view them.

The HP Pocket Playlist is HP’s first mobile NAS device. It can share stored Hulu or Netflix content which is loaded to it through PC software that ties in with the PlayLater option. For that matter, it can serve 5 Wi-Fi devices on its own.

Western Digital also launched the WD Black hybrid hard disks that integrate SSD and spinning-platter technology in a 2.5” housing. They would be pitched to OEMS for use with the next laptops or ultraportables.

Conclusion

Stay tuned to the last in this series which will encompass mobile technology as well as the smart home and automotive technology.

Integrated HomePlug AV Ethernet switch with power outlet

Article

Homeplug AV socket by Power Ethernet offers slimline speedy home networking – Recombu

From the horse’s mouth

Product page

My Comments

There is another way that the HomePlug technology is being taken further in the UK. Here, this device resembles a regular UK double power outlet and is installed in a regular double-gang wall bracket.

But you have a single 13-amp UK power outlet plus a 4-port 10/100 managed Ethernet switch. It then connects to a HomePlug AV 200Mbps powerline network segment that rides on the existing ring-main wiring. Business users who value functionality like VLANs can benefit from the Ethernet switch being a managed type.

The Website pitched this unit as being a network on-ramp or off-ramp for a HomePlug AV segment and cited applications like historic buildings where modifications to power outlet locations may be against the heritage-protection rules for these buildings.

Personally, I would recommend this kind of outlet to be compliant to HomePlug AV2 and would be best suited to projects where you are reorganising power outlets in a room or building. In the home, it would be more applicable for locations where a cluster of computing or audio-video equipment would exist. I would also value it as being useful for caravans or temporary buildings or, for that matter, any outbuilding application.

Similarly, the “Power Ethernet” unit could be made available with an integrated 802.11n Wi-Fi access point for “infill use” in covering wireless-network black spots but it is easy to think of this device as being something that can provide HomePlug in a semi-permanent manner.

A HomePlug AV 500Gbps switch–now with 4 Gigabit Ethernet ports

Articles

ZyXEL To Ship 500 Mbps Powerline Switch | SmallNetBuilder

From the horse’s mouth

Zyxel press release

My Comments

Gigabit Ethernet is now becoming the order of the day with most current desktop and laptop PCs as well as network-attached-storage units being equipped with such a port. This is being taken further with routers having to be equipped with Gigabit Ethernet LAN (and WAN) ports in order to be considered fit for next-generation broadband Internet. This situation is also augmented with basic 5-port and 8-port Gigabit Ethernet switches now becoming more affordable.

At the moment, most HomePlug AV-Ethernet switches have been equipped with Ethernet ports that can work to a link speed of 100Mbps. This wouldn’t work in an optimum manner if you are connecting Gigabit-Ethernet-equipped computers to a HomePlug AV segment.

What Zyxel have done now is that they have announced a HomePlug AV Ethernet switch, the PLA4225, that uses Gigabit Ethernet ports as well as working to the unqualified 500Gbps extension of the HomePlug standard. This could allow you to provide a proper high-throughput HomePlug AV on-ramp for your desktop or laptop computer; fully-compliant next-generation-broadband “edge” router and NAS with these devices working at speed.

This is also in conjunction with them releasing the PLA4205 “homeplug” that works to the same powerline-network standard but uses a single Gigabit Ethernet socket.

Personally, what I would like to see for all of these 500Gbps HomePlug AV devices is that they are able to work to the full HomePlug AV2 standard once it is ratified and a proper firmware update is delivered.

But what I am pleased about is that the Ethernet connectivity of this HomePlug hardware is up to standard for people who use next-generation broadband Internet services with the proper routers.

Devolo dLAN® 200 AVpro DINrail–a fixed HomePlug AV bridge for integration to a circuit-breaker board

Press Release – German language

devolo präsentiert ersten dLAN®-Hutschienenadapter für Smart Home- und Smart Metering-Anwendungen

Product Page – German language

dLAN® 200 AVpro DINrail … Produktbeschreibung … devolo AG

My Comments

Devolo have just released the dLAN 200 AVpro DINrail HomePlug AV-Ethernet bridge which is intended as a “built-in” HomePlug AV on-ramp.

Here, this unit is Intended to be installed by a professional electrician and is installed in a circuit-breaker board that works to the standard “DIN-rail” mount. When installed, there is an exposed Ethernet socket for connection to Ethernet-ended network equipment.

The main applications that this unit is being pitched at are energy-monitoring / control applications, especially with “smart meters” that have an Ethernet connection. In the same context, it could work with network-enabled HVAC equipment that uses an Ethernet connection but is direct-wired via the AC supply via an isolating switchboard.

It can then also apply to other integrated-wiring installations where you may want an Ethernet connection local to the power switchboard. An example of this could be a broom cupboard under the stairs which has the house’s main switchboard. Here, it could be tempting to hide the network-Internet “edge” equipment in that area and install the HomePlug “on-ramp” there, even if there is Ethernet or Wi-Fi access to the main Internet service available around the house.

Another example that would be relevant to HomePlug AV installations on larger properties is “pushing out” HomePlug AV coverage to remote buildings as I have explained here. This is where you have two different HomePlug AV segments connected via an Ethernet link and two of these Devolo DINrail units could be mounted in the garage’s or barn’s isolating switchboard and linked with a short Ethernet cable. Of course, one would be linked with the main HomePlug segment and the other to a unique segment that serves the barn and any buildings or caravans wired off it.

Other applications also include installations like some previous HomePlug backbone setups based around Devolo dLAN hardware that were used in a few German schools. Here, these installations used HomePlug as the network backbone.

It might also be easy to think of using this unit to build a “network-ready” isolating switchbox that is closed up. Here, a patch cord from the Devolo dLAN 200AVPro DINRail bridge’s Ethernet socket could be run to an Ethernet socket mounted on the side of the box, so as to connect up network-enabled equipment local to that switchbox.

An improvement that I would like to see for this unit would be a SimpleConnect button on the front of the unit so that customers can quickly associate regular HomePlug AV devices to this unit while keeping it as a “reference” unit for the segment that it is part of. This could be defeated through software for “smart-meter” environments and other environments where you don’t like the customer to “detach” the unit from an established network.

At least this unit could appeal to those of us who want the “integrated” HomePlug AV solution for our home networks. In addition, this could become a piece of kit that local “sparkies” could have available for sale and installation, especially if they cater to the connected home or small business.